In the 'SET' mode select manual input mode and set following parameters
INPUT DEVICE 1
1
INPUT DEVICE 2
1
INPUT UNIT
0
PUNCH CODE
1
TV CHECK
0
In the 'PARAM' mode set following parameters
#340
2
#341
2
#310,#311,#312,#313 (baud rate) = 0000 1001
Baud
Parameter value
1200
0000 0111
2400
0000 1000
4800
0000 1001
9600
0000 1010
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0-P
Serial port
COM2 (or any free COM port)
Baud
4800
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Press function key several times or press soft key [SETTING] to display SETTING (HANDY) screen.
Set the cursor to PARAMETER WRITE and, press and keys in this order. Here alarm 100 will be displayed.
Press function key several times to display parameters screen.
. Set the following parameters:
IO CHANNEL
0
TAPE FORMAT
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode 'Offset Setting -> System -> Parameter (setting) and set following parameters
#0000 (ISO mode)
0000 0010 (TVC=0, TV check off; ISO=1, ISO mode enabled)
#0020 (IO Channel)
0 (Channel 1, RS232, JD56A of mother board)
#0100 (Program format)
NCR=1, CRF=0, Line end format: LF, ND3=1 - drip feed mode
#0101 (Stop bit and other data)
1000 0001 (NFD=1, Feed is not output; ASI=0, ISO mode; SB2=1, two stop bits)
#0102 (Device number)
0 (RS-232)
#0103 (Baud rate)
9 (2400)
#0134 (Parity)
PRY=1 (Use parity checking, power off/on machine after changing)
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0I-M
Serial port
COM2 (or any free COM port)
Baud
9600
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Press function key several times or press soft key [SETTING] to display SETTING (HANDY) screen.
Set the cursor to PARAMETER WRITE and, press and keys in this order. Here alarm 100 will be displayed.
Press function key several times to display parameters screen.
. Set the following parameters:
IO CHANNEL
0
TAPE FORMAT
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode 'Offset Setting -> System -> Parameter (setting) and set following parameters
#0000 (ISO mode)
0000 0010 (TVC=0, TV check off; ISO=1, ISO mode enabled)
#0020 (IO Channel)
0 (Channel 1, RS232, JD56A of mother board)
#0100 (Program format)
NCR=1, CRF=0, Line end format: LF, ND3=1 - drip feed mode
#0101 (Stop bit and other data)
1000 0001 (NFD=1, Feed is not output; ASI=0, ISO mode; SB2=1, two stop bits)
#0102 (Device number)
0 (RS-232)
#0103 (Baud rate)
9 (2400)
#0134 (Parity)
PRY=1 (Use parity checking, power off/on machine after changing)
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0I-T
Serial port
COM2 (or any free COM port)
Baud
9600
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Press the [Parameters] button for parameters settings
Press the [PAGE DOWN] button and select the 'Settings 2' submode
Set the 'MODE SELECT' switch to 'MDI'
Set the 'NO PWE' parameter to 1 and press the 'Input' button. After changing parameters below, change this value to 0 again
Select the 'Settings 2' submode
Set I/O = 1
Server mode. This machines has a very limited set of characters. Therefore you should use the following format of the command program
%
N0010 P0001
Where P0001 request for the 0001 program
%
With help of 'PAGE DOWN' and 'PAGE UP' buttons change bits in the following parameters. Please, don't change bits that didn't print in the table below
#0002 (IO settings for IO device 0)
bit 0
1 (2 stop bits)
bit 2
0 (RS232)
bit 3
0 (ISO mode)
bit 7
0 (No tape leader)
#0018 (TV check)
bit 6
0 (Off)
#0038 (IO device selection)
bit 4
0
bit 5
1
bit 6
0
bit 7
1
#0055 (Additional parameters)
bit 0
1 (ASCII)
bit 1
0 (CR)
bit 2
0 (Protocol A)
bit 3
0 (RS232)
#0552 (baud rate for IO Device 0). Set this parameter = 9
Baud
Parameter value
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0M-C
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Press the [Parameters] button for parameters settings
Press the [PAGE DOWN] button and select the 'Settings 2' submode
Set the 'MODE SELECT' switch to 'MDI'
Set the 'NO PWE' parameter to 1 and press the 'Input' button. After changing parameters below, change this value to 0 again
Select the 'Settings 2' submode
Set I/O = 1
Server mode. This machines has a very limited set of characters. Therefore you should use the following format of the command program
%
N0010 P0001
Where P0001 request for the 0001 program
%
With help of 'PAGE DOWN' and 'PAGE UP' buttons change bits in the following parameters. Please, don't change bits that didn't print in the table below
#0002 (IO settings for IO device 0)
bit 0
1 (2 stop bits)
bit 2
0 (RS232)
bit 3
0 (ISO mode)
bit 7
0 (No tape leader)
#0018 (TV check)
bit 6
0 (Off)
#0038 (IO device selection)
bit 4
0
bit 5
1
bit 6
0
bit 7
1
#0055 (Additional parameters)
bit 0
1 (ASCII)
bit 1
0 (CR)
bit 2
0 (Protocol A)
bit 3
0 (RS232)
#0552 (baud rate for IO Device 0). Set this parameter = 9
Baud
Parameter value
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0M-D
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Press the [Parameters] button for parameters settings
Press the [PAGE DOWN] button and select the 'Settings 2' submode
Set the 'MODE SELECT' switch to 'MDI'
Set the 'NO PWE' parameter to 1 and press the 'Input' button. After changing parameters below, change this value to 0 again
Select the 'Settings 2' submode
Set I/O = 1
Server mode. This machines has a very limited set of characters. Therefore you should use the following format of the command program
%
N0010 P0001
Where P0001 request for the 0001 program
%
With help of 'PAGE DOWN' and 'PAGE UP' buttons change bits in the following parameters. Please, don't change bits that didn't print in the table below
#0002 (IO settings for IO device 0)
bit 0
1 (2 stop bits)
bit 2
0 (RS232)
bit 3
0 (ISO mode)
bit 7
0 (No tape leader)
#0018 (TV check)
bit 6
0 (Off)
#0038 (IO device selection)
bit 4
0
bit 5
1
bit 6
0
bit 7
1
#0050 (Parity)
bit 1
1 (Check parity)
#0055 (Additional parameters)
bit 0
1 (ASCII)
bit 1
0 (CR)
bit 2
0 (Protocol A)
bit 3
0 (RS232)
#0552 (baud rate for IO Device 0). Set this parameter = 9
Baud
Parameter value
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0M
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Press the [Parameters] button for parameters settings
Press the [PAGE DOWN] button and select the 'Settings 2' submode
Set the 'MODE SELECT' switch to 'MDI'
Set the 'NO PWE' parameter to 1 and press the 'Input' button. After changing parameters below, change this value to 0 again
Select the 'Settings 2' submode
Set I/O = 1
With help of 'PAGE DOWN' and 'PAGE UP' buttons change bits in the following parameters. Please, don't change bits that didn't print in the table below
#002 (stop bit and data format)
bit 0
0 (1 stop bit)
bit 2
0 (RS232)
bit 3
1 (ASCII)
#0552 (baud rate). Set this parameter = 9
Baud
Parameter value
2400
9
4800
10
9600
11
19200
12
#0038 (IO device)
bit 1
0
bit 2
1
bit 4
0
bit 5
1
bit 6
0
bit 7
1
#0051 (Parity)
bit 1
1 (Yes)
#0055 (Additional parameters)
bit 0
1 (ASCII)
bit 1
0 (CR)
bit 2
0 (Protocol A)
bit 3
0 (RS232)
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Press the [Parameters] button for parameters settings
Press the [PAGE DOWN] button and select the 'Settings 2' submode
Set the 'MODE SELECT' switch to 'MDI'
Set the 'NO PWE' parameter to 1 and press the 'Input' button. After changing parameters below, change this value to 0 again
Select the 'Settings 2' submode
Set I/O = 1
With help of 'PAGE DOWN' and 'PAGE UP' buttons change bits in the following parameters. Please, don't change bits that didn't print in the table below
#002 (stop bit and data format)
bit 0
0 (1 stop bit)
bit 2
0 (RS232)
bit 3
1 (ASCII)
#0552 (baud rate). Set this parameter = 9
Baud
Parameter value
2400
9
4800
10
9600
11
19200
12
#0038 (IO device)
bit 1
0
bit 2
1
bit 4
0
bit 5
1
bit 6
0
bit 7
1
#0051 (Parity)
bit 1
1 (Yes)
#0055 (Additional parameters)
bit 0
1 (ASCII)
bit 1
0 (CR)
bit 2
0 (Protocol A)
bit 3
0 (RS232)
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 0TC
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Set the 'PWE' parameter #8000 (Enable changing parameters) to ON (all bits = 1). After changing parameters below, change this value to OFF (all bits = 0).
#5001
1
#5002
2
#5003
3
#5110
4
#5111
2
#5112
9
#5120
4
#5121
2
#5122
9
#5130
4
#5131
2
#5132
9
#0010
1
#0021
1
#0022
1
#0023
1
If you want, you can change baud rate (#5112,#5122,#5132)
Baud
Parameter value
2400
8
2400
9
4800
10
9600
11
Set additional parameters #0000
Name
Value
TVC
0
CTV
1
ISP
0
NCR
0
EIA
0
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 10M
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Set the 'PWE' parameter #8000 (Enable changing parameters) to ON (all bits = 1). After changing parameters below, change this value to OFF (all bits = 0).
#5001
1
#5002
2
#5003
3
#5110
4
#5111
2
#5112
9
#5120
4
#5121
2
#5122
9
#5130
4
#5131
2
#5132
9
#0010
1
#0021
1
#0022
1
#0023
1
If you want, you can change baud rate (#5112,#5122,#5132)
Baud
Parameter value
2400
8
2400
9
4800
10
9600
11
Set additional parameters #0000
Name
Value
TVC
0
CTV
1
ISP
0
NCR
0
EIA
0
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 10T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Set the 'PWE' parameter #8000 (Enable changing parameters) to ON (all bits = 1). After changing parameters below, change this value to OFF (all bits = 0).
#5001
1
#5002
2
#5003
3
#5110
4
#5111
2
#5112
9
#5120
4
#5121
2
#5122
9
#5130
4
#5131
2
#5132
9
#0010
1
#0021
1
#0022
1
#0023
1
If you want, you can change baud rate (#5112,#5122,#5132)
Baud
Parameter value
2400
8
2400
9
4800
10
9600
11
Set additional parameters #0000
Name
Value
TVC
0
CTV
1
ISP
0
NCR
0
EIA
0
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 11T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Set the 'PWE' parameter #8000 (Enable changing parameters) to ON (all bits = 1). After changing parameters below, change this value to OFF (all bits = 0).
#5001
1
#5002
2
#5003
3
#5110
4
#5111
2
#5112
9
#5120
4
#5121
2
#5122
9
#5130
4
#5131
2
#5132
9
#0010
1
#0021
1
#0022
1
#0023
1
If you want, you can change baud rate (#5112,#5122,#5132)
Baud
Parameter value
2400
8
2400
9
4800
10
9600
11
Set additional parameters #0000
Name
Value
TVC
0
CTV
1
ISP
0
NCR
0
EIA
0
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 12M
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Set the 'PWE' parameter #8000 (Enable changing parameters) to ON (all bits = 1). After changing parameters below, change this value to OFF (all bits = 0).
#5001
1
#5002
2
#5003
3
#5110
4
#5111
2
#5112
9
#5120
4
#5121
2
#5122
9
#5130
4
#5131
2
#5132
9
#0010
1
#0021
1
#0022
1
#0023
1
If you want, you can change baud rate (#5112,#5122,#5132)
Baud
Parameter value
2400
8
2400
9
4800
10
9600
11
Set additional parameters #0000
Name
Value
TVC
0
CTV
1
ISP
0
NCR
0
EIA
0
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 12T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Set the 'PWE' parameter #8000 (Enable changing parameters) to ON (all bits = 1). After changing parameters below, change this value to OFF (all bits = 0).
#5001
1
#5002
2
#5003
3
#5110
5
#5111
2
#5112
9
#5120
4
#5121
2
#5122
9
#5130
4
#5131
2
#5132
9
#0010
1
#0021
1
#0022
1
#0023
1
If you want, you can change baud rate (#5112,#5122,#5132)
Baud
Parameter value
2400
8
2400
9
4800
10
9600
11
Set additional parameters #0000
Name
Value
TVC
0
CTV
1
ISP
0
NCR
0
EIA
0
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 15M
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
Set the 'PWE' parameter #8000 (Enable changing parameters) to ON (all bits = 1). After changing parameters below, change this value to OFF (all bits = 0).
#5001
1
#5002
2
#5003
3
#5110
4
#5111
2
#5112
9
#5120
4
#5121
2
#5122
9
#5130
4
#5131
2
#5132
9
#0010
1
#0021
1
#0022
1
#0023
1
If you want, you can change baud rate (#5112,#5122,#5132)
Baud
Parameter value
2400
8
2400
9
4800
10
9600
11
Set additional parameters #0000
Name
Value
TVC
0
CTV
1
ISP
0
NCR
0
EIA
0
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 15T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
TAPE FORMAT
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode 'Offset Setting -> System -> Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
9
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 16M
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
TAPE FORMAT
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode 'Offset Setting -> System -> Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
9
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 16P
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
TAPE FORMAT
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode 'Offset Setting -> System -> Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
9
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 16T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode Offset Setting | System | Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
9
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 18IT
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode Offset Setting | System | Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
9
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 18M
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode Offset Setting | System | Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
9
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 18T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode Offset Setting | System | Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
11
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 21M
Serial port
COM2 (or any free COM port)
Baud
9600
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode Offset Setting | System | Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
11
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 21T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A#0D#0D
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: :
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
IO CHANNEL
0
PUNCH CODE
1
TV CHECK
0
Please, select following mode Offset Setting | System | Parameter (setting) and set following parameters
#0000
0000 0010
#0020 (IO Channel)
0 (RS232)
#0100
0
#0101 (NFD)
1000 0001
#0102 (Device number)
0
#0103
11
If you want you can change baud rate in the parameter #0103 to:
Baud
Parameter value
1200
8
2400
9
4800
10
9600
11
19200
12
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 21TB
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
INPUT DEVICE 1
1
INPUT DEVICE 2
1
INPUT UNIT
0
PUNCH CODE
1
TV CHECK
0
In the 'PARAM' mode set following parameters
#340
2
#341
2
#310,#311,#312,#313 (baud rate) = 0000 1001
Baud
Parameter value
1200
0000 0111
2400
0000 1000
4800
0000 1001
9600
0000 1010
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 6M
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
In the 'SET' mode select manual input mode and set following parameters
INPUT DEVICE 1
1
INPUT DEVICE 2
1
INPUT UNIT
0
PUNCH CODE
1
TV CHECK
0
In the 'PARAM' mode set following parameters
#340
2
#341
2
#310,#311,#312,#313 (baud rate) = 0000 1001
Baud
Parameter value
1200
0000 0111
2400
0000 1000
4800
0000 1001
9600
0000 1010
Set the following parameters on the PC
Serial port tab
Machine name
Fanuc 6T
Serial port
COM2 (or any free COM port)
Baud
2400
Data bits
7
Parity
Even
Stop bits
2
Data flow control tab
Use DTR
False
Use RTS
True
Require DSR
False
Require CTS
True
Set RTS
False
Set DTR
False
Software flowcontrol
None
Xon char
#11
Xoff char
#13
Data exchange format tab
Format mode
Uniform
Format parameters
Program start: %
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No
