DNC and CNC setting for Mazak
These settings are for the DNC Precision software only. They may not work with other software.
Mazak - Fusion 640M - Machine parameters
Set the following parameters on the machine
| Baud rate | 9600 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
| Handshake | DC control |
| Wait time | 45 sec |
| Format | 7 |
| Same Wno. | ALARM |
| Port | COM1 |
| TAP1 | 1 |
| TAP2 | 0 |
| TAP3 | 0 |
| TAP4 | 0 |
| TAP5 | 1 |
| TAP6 | 0 |
| TAP7 | 0 |
| TAP8 | 8 |
| TAP9 | 76 |
| TAP10 | 13 |
| TAP11 | 109 |
| TAP12 | 122 |
| TAP13 | 91 |
| TAP14 | 70 |
| TAP15 | 0 |
| TAP16 | 0 |
| TAP17 | 0 |
| TAP18 | 0 |
| TAP19 | 0 |
| TAP20 | 0 |
| TAP21 | 0 |
| TAP22 | 0 |
| TAP23 | 0 |
| TAP24 | 0 |
| TAP25 | 00000000 |
| TAP26 | 00000001 |
| TAP27 | 00000000 |
| TAP28 | 00111010 |
| TAP29 | 10 |
| TAP30 | 30 |
| TAP31 | 0 |
| TAP32 | 0 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - Fusion 640M |
| Serial port | COM2 (or any free COM port) |
| Baud | 9600 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | Both |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start: %
Program end: %
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No |
Mazak - Fusion 640T - DNC settings
Set the following parameters on the machine
| Baud rate | 9600 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
| Handshake | DC control |
| Wait time | 45 sec |
| Format | 7 |
| Same Wno. | ALARM |
| Port | COM1 |
| TAP1 | 1 |
| TAP2 | 0 |
| TAP3 | 0 |
| TAP4 | 0 |
| TAP5 | 1 |
| TAP6 | 0 |
| TAP7 | 0 |
| TAP8 | 8 |
| TAP9 | 76 |
| TAP10 | 13 |
| TAP11 | 109 |
| TAP12 | 122 |
| TAP13 | 91 |
| TAP14 | 70 |
| TAP15 | 0 |
| TAP16 | 0 |
| TAP17 | 0 |
| TAP18 | 0 |
| TAP19 | 0 |
| TAP20 | 0 |
| TAP21 | 0 |
| TAP22 | 0 |
| TAP23 | 0 |
| TAP24 | 0 |
| TAP25 | 00000000 |
| TAP26 | 00000001 |
| TAP27 | 00000000 |
| TAP28 | 00111010 |
| TAP29 | 10 |
| TAP30 | 30 |
| TAP31 | 0 |
| TAP32 | 0 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - Fusion 640T |
| Serial port | COM2 (or any free COM port) |
| Baud | 9600 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | Both |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start: %
Program end: %
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No |
Mazak - L32 - DNC settings
Set the following parameters on the machine
| Note: | The program does not support the Mazatrol protocol |
| Change CNC parameters |
| FD I/O Mode | 1 (ISO) |
| FD I/O STOP BIT | 2 (2 bits) |
| FD I/O PARITY | 0 (No Parity, but in DNCP you should use the Even parity) |
| FD I/O BAUD RATE | 9600 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - L32 |
| Serial port | COM2 (or any free COM port) |
| Baud | 9600 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | Both |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start: %
Program end: %
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: Yes
Program ending characters in the file: Yes |
Mazak - M plus - NC settings
Set the following parameters on the machine
| Note: | The program does not support the Mazatrol protocol |
| Change user parameter #5 |
| G1 (baud rate) | 1 (9600) |
| G2 (stop bits) | 3 (2 stop bits) |
| G3 (parity) | 0 (Even) |
| G5 (data bits) | 3 (8 data bits, but in the program you should specify 7 ) |
| G6 (Terminattors) | 1 (EOB or EOR) |
| G10 | 3 (Use DC handshaking) |
| G11 | 1 (Parity on DC output) |
| G12 | 0 (Don't output DC2 and DC4) |
| G13 (wait time) | 50 |
| G17 | 00000000 |
| G31 | 00000000 |
| G33 (feed section size) | 50 |
| G34 (number of spaces) | 10 |
| G39 | 00000100 |
| G40 | 00000000 |
| G48 | 0 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - M plus |
| Serial port | COM2 (or any free COM port) |
| Baud | 9600 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | Both |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start: %
Program end: %
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No |
Mazak - M32 plus - Machine parameters
Set the following parameters on the machine
| Note: | The program does not support the Mazatrol protocol |
| Change user parameter #5 |
| G1 (baud rate) | 2 (4800) |
| G2 (stop bits) | 3 (2 stop bits) |
| G3 (parity) | 0 (Even) |
| G5 (data bits) | 3 (8 data bits, but in the program you should specify 7 ) |
| G6 (Terminattors) | 1 (EOB or EOR) |
| G7 | 0 |
| G8 | 0 |
| G9 | 0 |
| G10 | 1 |
| G11 | 1 |
| G12 | 0 |
| G13 (wait time) | 50 |
| G14 | 0 |
| G15 | 0 |
| G16 | 0 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - M32 plus |
| Serial port | COM2 (or any free COM port) |
| Baud | 4800 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | None |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start: %
Program end: %
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No |
Mazak - M32 - DNC settings
Set the following parameters on the machine
| Note: | The program does not support the Mazatrol protocol |
| Change user parameter #5 |
| G19 (baud rate) | 2 (4800) |
| G20 (stop bits) | 3 (2 stop bits) |
| G22 (parity) | 0 (Even) |
| G23 (data bits) | 3 (8 data bits, but in the program you should specify 7 ) |
| G24 | 1 |
| G25 | 0 |
| G26 | 0 |
| G27 (ISO CR output) | 0 |
| G28 | 0 |
| G29 (handshake type) | 3 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - M32 |
| Serial port | COM2 (or any free COM port) |
| Baud | 4800 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | None |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start: %
Program end: %
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: :
Program starting characters in the file: No
Program ending characters in the file: No |
Mazak - T plus - NC settings
Set the following parameters on the machine
| Note: | The program does not support the Mazatrol protocol |
| I1 | 2 |
| I2 | 3 |
| I3 | 0 |
| I4 | 0 |
| I5 | 3 |
| I6 | 3 |
| I7 | 1 |
| I8 | 5 |
| I9 | 0 |
| I10 | 1 |
| I11 | 1 |
| I12 | 0 |
| I13 | 0 |
| I14 | 0 |
| I15 | 30 |
| I16 | 0 |
| I24 | 0 |
| I58 | 0000 0000 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - T plus |
| Serial port | COM2 (or any free COM port) |
| Baud | 4800 |
| Data bits | 8 |
| Parity | None |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | Both |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No |
Mazak - T2 - Machine parameters
Set the following parameters on the machine
| Note: | The program does not support the Mazatrol protocol |
| A15 (RS-232) | 206 |
| A16 (parity) | 1 (None, but in a program configuration you should specify 7 data bits and Even parity) |
| A17 (baud rate) | 6 (4800) |
| A18 (mode) | 6 (read and punch) |
| A19 | 0 |
| A20 (punch code) | 1 (ISO) |
| A21 | 1 |
| A22 | 10 |
| A23 | 10 |
| A24 (TV check) | 0 |
| A30 | 3 |
| A31 | 109 |
| A31 | 70 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - T2 |
| Serial port | COM2 (or any free COM port) |
| Baud | 4800 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 1 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | Both |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No |
Mazak - T32 M2 - NC settings
Set the following parameters on the machine
| Note: | The program does not support the Mazatrol protocol |
| I1 | 2 |
| I2 | 3 |
| I3 | 0 |
| I4 | 0 |
| I5 | 3 |
| I6 | 3 |
| I7 | 1 |
| I8 | 5 |
| I9 | 0 |
| I10 | 1 |
| I11 | 1 |
| I12 | 0 |
| I13 | 0 |
| I14 | 0 |
| I15 | 30 |
| I16 | 0 |
| I24 | 0 |
| I58 | 0000 0000 |
Set the following parameters on the PC
Serial port tab
| Machine name | Mazak - T32 M2 |
| Serial port | COM2 (or any free COM port) |
| Baud | 4800 |
| Data bits | 7 |
| Parity | Even |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | Both |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No |
Null modem cable, without handshake
PC, 9pin, DB9M | CNC, 25pin, DB25
Null modem cable, without handshake
PC, 25pin, DB25M | CNC, 25pin, DB25
Null modem cable, without handshake
PC, 9pin, DB9M | CNC, 25pin, DB25
Null modem cable, with full handshake
PC, 9pin, DB25M | CNC, 25pin, DB25
Null modem cable, without handshake
PC, 25pin, DB25M | CNC, 25pin, DB25
Null modem cable, with full handshake
PC, 25pin, DB25M | CNC, 25pin, DB25
Go to Index page
Maho - CNC 432 - 2000
Leadwell - V80i
Mikron CNC
Milltronics - VM-20
If you connected DNC Precision to another controller that is not on this list, please send us the information so we can add it to the list.
