bg

DNC and CNC setting for Heidenhain

These settings are for the DNC Precision software only. They may not work with other software.

Heidenhain-CNC Pilot - Machine parameters

Set the following parameters on the machine

Press the [Parameter] button, then select Configure, then Control direct, then Enter parameter #42 and change
Baud rate15 (19200)
Word length1 (7 bits)
Parity1 (Even)
Stop bits0 (One)
Protocol0 (Hardware)

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-CNC Pilot
Serial portCOM2 (or any free COM port)
Baud19200
Data bits7
ParityEven
Stop bits1

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No

Heidenhain-TNC 145 - NC settings

Set the following parameters on the machine

Enter to editing parameters mode by 95148 code. Press [DEL] twice for exit.
Interface typeEXT
Baud rate9600
MP222 (data format)104
MP92 (multi function)1

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-TNC 145
Serial portCOM2 (or any free COM port)
Baud9600
Data bits7
ParityEven
Stop bits2

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: PGM
Program starting characters in the file: No
Program ending characters in the file: No

Heidenhain-TNC 150 - Machine parameters

Set the following parameters on the machine

Enter to editing parameters mode by 95148 code. Press [DEL] twice for exit.
Interface typeEXT
Baud rate9600
MP222 (data format)104
MP92 (multi function)1

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-TNC 150
Serial portCOM2 (or any free COM port)
Baud2400
Data bits7
ParityEven
Stop bits2

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: PGM
Program starting characters in the file: No
Program ending characters in the file: No

Heidenhain-TNC 155 - NC settings

Set the following parameters on the machine

Enter to editing parameters mode by 95148 code. Press [DEL] twice for exit.
Interface typeEXT
Baud rate9600
MP222 (data format)104
MP92 (multi function)1

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-TNC 155
Serial portCOM2 (or any free COM port)
Baud2400
Data bits7
ParityEven
Stop bits2

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end: %
Line start:
Line end: #0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: PGM
Program starting characters in the file: No
Program ending characters in the file: No

Heidenhain-TNC 2500 - Machine parameters

Set the following parameters on the machine

MP5200 (data format)100
MP5030 (interface type)0

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-TNC 2500
Serial portCOM2 (or any free COM port)
Baud2400
Data bits7
ParityEven
Stop bits2

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No

Heidenhain-TNC 407 - Machine parameters

Set the following parameters on the machine

Interface typeEXT2
Baud rate9600
MP5200.1 (external device)2
MP5201.1 (external device)3
MP5020.1104
MP5030.10

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-TNC 407
Serial portCOM2 (or any free COM port)
Baud2400
Data bits7
ParityEven
Stop bits2

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No

Heidenhain-TNC 415B - Machine parameters

Set the following parameters on the machine

Interface typeEXT2
Baud rate9600
MP5200.1 (external device)2
MP5201.1 (external device)3
MP5020.1104
MP5030.10

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-TNC 415B
Serial portCOM2 (or any free COM port)
Baud9600
Data bits7
ParityEven
Stop bits2

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No

Heidenhain-TNC 425 - DNC settings

Set the following parameters on the machine

Interface typeEXT2
Baud rate9600
MP5200.1 (external device)2
MP5201.1 (external device)3
MP5020.1104
MP5030.10

Set the following parameters on the PC

Serial port tab

Machine nameHeidenhain-TNC 425
Serial portCOM2 (or any free COM port)
Baud2400
Data bits7
ParityEven
Stop bits2

Data flow control tab

Use DTRFalse
Use RTSTrue
Require DSRFalse
Require CTSTrue
Set RTSFalse
Set DTRFalse
Software flowcontrolNone
Xon char#11
Xoff char#13

Data exchange format tab

Format modeUniform
Format parametersProgram start:
Program end:
Line start:
Line end: #0D#0A
Skip lines:
Ignore characters: No characters for remove
Remove blank lines: No
Program name prefix: O
Program starting characters in the file: No
Program ending characters in the file: No

Null modem cable, without handshake
PC, 9pin, DB9M | CNC, 25pin, DB25
 

Null modem cable, with full handshake
PC, 9pin, DB25M | CNC, 25pin, DB25
 

Null modem cable, without handshake
PC, 25pin, DB25M | CNC, 25pin, DB25
 

Null modem cable, with full handshake
PC, 25pin, DB25M | CNC, 25pin, DB25
 

Go to Index page
Haas Mill
Haas Lathe
Hinumerik 2000M
Hitachi Seikos

If you connected DNC Precision to another controller that is not on this list, please send us the information so we can add it to the list.