DNC and CNC setting for Dialog
These settings are for the DNC Precision software only. They may not work with other software.
Dialog-11 - DNC settings
Set the following parameters on the machine
Set the following parameters on the PC
Serial port tab
| Machine name | Dialog-11 |
| Serial port | COM2 (or any free COM port) |
| Baud | 4800 |
| Data bits | 7 |
| Parity | None |
| Stop bits | 1 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | None |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start:
Program end: M30
Line start:
Line end: #0D#0A
Skip lines: ;
Ignore characters: No characters for remove
Remove blank lines: Yes
Program name prefix:
Program starting characters in the file: No
Program ending characters in the file: Yes |
Dialog-2 - NC settings
Set the following parameters on the machine
| The machine parameters can be set using the DIP switches available on the control panel. |
| This machine does not have an RS232C interface. K5 connector is available for audio interface must be connected to a DB-25 connector (which must be fixed to the panel) |
| DB25 | K5 |
| 1 | 11,12 |
| 2 | 17 |
| 3 | 13 |
| 4 | 20 |
| 5 | 16 |
| 6 | 18 |
| 7 | 11,12 |
| 6 connect with 20 |
Set the following parameters on the PC
Serial port tab
| Machine name | Dialog-2 |
| Serial port | COM2 (or any free COM port) |
| Baud | 9600 |
| Data bits | 7 |
| Parity | None |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | None |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start:
Program end: M30
Line start:
Line end: #0D#0A
Skip lines: ;
Ignore characters: No characters for remove
Remove blank lines: Yes
Program name prefix:
Program starting characters in the file: No
Program ending characters in the file: Yes |
Dialog-4 - NC settings
Set the following parameters on the PC
Serial port tab
| Machine name | Dialog-4 |
| Serial port | COM2 (or any free COM port) |
| Baud | 2400 |
| Data bits | 7 |
| Parity | None |
| Stop bits | 2 |
Data flow control tab
| Use DTR | False |
| Use RTS | True |
| Require DSR | False |
| Require CTS | True |
| Set RTS | False |
| Set DTR | False |
| Software flowcontrol | None |
| Xon char | #11 |
| Xoff char | #13 |
Data exchange format tab
| Format mode | Uniform |
| Format parameters | Program start: &%
Program end: M30#0D#0A
Line start:
Line end: #0D#0A
Skip lines: ;
Ignore characters: No characters for remove
Remove blank lines: Yes
Program name prefix:
Program starting characters in the file: No
Program ending characters in the file: Yes |
Null modem cable, without handshake
PC, 9pin, DB9M | CNC, 25pin, DB25
Null modem cable, with full handshake
PC, 9pin, DB25M | CNC, 25pin, DB25
Null modem cable, without handshake
PC, 25pin, DB25M | CNC, 25pin, DB25
Null modem cable, with full handshake
PC, 25pin, DB25M | CNC, 25pin, DB25
Go to Index page
Delta Dynapath
DOOSAN HM630
Digma CNC
Eckelmann - Viewstar 750
If you connected DNC Precision to another controller that is not on this list, please send us the information so we can add it to the list.
